TP Link Switch TL SL1117 User Manual

User Guide  
TL-SL1210  
8-Port 10/100Mbps + 2-Port Gigabit Switch  
TL-SL1117  
16-Port 10/100Mbps + 1-Port Gigabit Switch  
TL-SL1226  
24-Port 10/100Mbps + 2-Port Gigabit Switch  
TL-SL1351  
48-Port 10/100Mbps + 3-Port Gigabit Switch  
Rev: 2.0.0  
7106503252  
 
EC DECLARATION OF CONFORMITY (EUROPE)  
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/  
EEC, this product meets the requirements of the following standards:  
¾
¾
¾
EN55022  
EN55024  
EN60950  
CE MARK WARNING  
This is a class A product. In a domestic environment, this product may cause radio  
interference, in which case the user may be required to take adequate measures.  
SAFETY NOTICES  
Cautions:  
Do not use this product near water, for example, in a wet basement or near a  
swimming pool.  
Avoid using this product during an electrical storm. There may be a remote risk of  
electric shock from lightning.  
 
Package Contents  
The following items should be found in your box:  
¾
¾
¾
¾
¾
One Switch  
One power cord  
This User's Guide  
Rubber footpads for Desk-mount  
Rack-mount kit for installing the switch in a 19-inch rack  
Note:  
Make sure that the package contains the above items. If any of the listed items are  
damaged or missing, please contact with your distributor.  
Chapter 1 Introduction of the Product  
This chapter describes the features of the TL-SL1210 / TL-SL1117 / TL-SL1226 /  
TL-SL1351 Gigabit Switch. TL-SL1210, TL-SL1117, TL-SL1226 and TL-SL1351  
just differ in the number of LED indicators and ports, and all figures in this user  
guide are of TL-SL1351.  
1.1 Overview of the product  
The TL-SL1210/TL-SL1117/TL-SL1226/TL-SL1351 Gigabit Switch provides you  
with a high-performance, low-cost, easy-to-use, seamless and standard upgrade  
to boost your old network to 1000Mbps. Increase the speed of your network server  
and backbone connections, make Gigabit connection to a server or uplink a  
network necessarily.  
The TP-LINK TL-SL1210/TL-SL1117/TL-SL1226/TL-SL1351 features a non-  
blocking switching architecture that forwards and filters packets at full wire-speed  
for maximum throughput. MAC address auto-learning and auto-aging, IEEE802.3x  
flow control for Full Duplex mode and backpressure for Half Duplex mode. It is  
compatible with all 10,100, and 1000Mbps Ethernet devices because it is  
standard-based.  
The TL-SL1210/TL-SL1117/TL-SL1226/TL-SL1351 is plug-and-play and no  
configuration is required. Auto MDI/MDIX cable detection on all ports eliminate the  
need for crossover cable or Uplink port. Each port can be used as general ports or  
1
 
       
Uplink ports, and any port can be simply plugged into a server, a hub, a router or a  
switch, using the straight cable or crossover cable. Diagnostic LEDs which display  
link status and activity, allowing you to quickly detect and correct problems on the  
network.  
1.2 Features  
¾
Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z (for TL-  
SL1351 only) standards  
¾
¾
¾
¾
8/16/24/48 10/100Mbps Auto-Sense RJ45 ports supporting Auto-MDI/MDIX  
2/1/2/2 10/100/1000Mbps Auto-Sense RJ45 ports supporting Auto-MDI/MDIX  
1 SFP(Small Form Pluggable) module interface (For TL-SL1351 only)  
Supports Auto MDI / MDIX cable detection on all ports eliminate the need for  
crossover cable or Uplink port  
¾
Non-blocking switching architecture that forwards and filters packets at full  
wire -speed for maximum throughput  
¾
¾
Supports MAC address auto-learning and auto-aging  
Supports IEEE802.3x flow control for full-duplex model and backpressure for  
half-duplex transfer model  
¾
¾
LED indicators for monitoring power, link, activity, speed  
Internal power supply  
Chapter 2 Installation  
2.1 Mounting the Switch on a Desk  
Before place the Switch on a desk, attach four rubber footpads to the flutes on the  
Switch bottom, then lay the Switch on the desktop, where can be have as much as  
5kg placed on top.  
Note:  
Make sure there is a grounded AC outlet within 1.5 meters, and working well.  
Make sure there is free space for radiating heat and air. Make sure not to place  
anything too heavy on top of the switch.  
2
 
       
2.2 Mounting the Switch in a Rack  
The dimension of TL-SL1210/TL-SL1117/TL-SL1226/TL-SL1351 is designed  
according to the standard 19'' rack- mountable steel case of Electronic Industries  
Association.  
Turn off all the equipment connected to the Switch before mounting it in the rack,  
then rivet the two “L” brackets onto each side of the Switch, fasten it with screws in  
the rack.  
Note:  
For TL-SL1210, the “L” brackets will differ in size.  
Figure 2-1 Rivet the ‘L’brackets onto the Switch  
Figure 2-2 Fasten the Switch in the rack  
3
 
   
2.3 Mounting the SFP Module (for TL-SL1351 Only)  
The front panel of the TL-SL1351 consists of a SFP module, which support The  
Hot Plug- And- Draw. Should fixed the SFP into SFP pluggable when use the SFP  
module. The switch could identify and configure the SFP module automatically.  
2.4 Power on  
TL-SL1210/TL-SL1117/TL-SL1226/TL-SL1351 Gigabit Switch is powered by AC  
power supply. Powering on the Switch, it will automatically initialize and its LED  
indicators should respond as follows:  
1) All of the LED indicators will flash momentarily for one second, which  
represents a resetting of the system.  
2) The power LED indicator will remain ON.  
Chapter 3 Identifying External Components  
This Chapter describes the front panel, rear panel and LED indicators of the  
Switch (here takes TL-SL1351 for example).  
3.1 Front Panel  
The front panel of TL-SL1351 consists of switch LED indicators, 48 10/100Mbps  
RJ-45 ports, 2 10/100/1000Mbps RJ-45 ports and 1 SFP module.  
Note:  
The SFP module is only for TL-SL3151.  
Figure 3-1 TL-SL1351 Switch Front Panel sketch  
The LED indicators include Power, Link/Act, 1000Mbps and 100Mbps LED  
indicators, which are used for monitoring and pre-troubleshooting of the Switch.  
The following section explains the status of LED indicators for the Switch along  
with an explanation of each indicator.  
¾
Power LED: This indicator will light solid red when the Switch powers up. If  
the LED is not lit, please check the power supply and connection.  
4
 
         
¾
¾
¾
1000M LED: The corresponding gigabit port LED indicator will light solid  
green when the gigabit port connected to a 1000Mbps device. It flashes green  
when data is being transmitted or received on the working connection.  
100M LED: The corresponding 100M port LED indicator will light solid green  
when the 10/100M port connected to a 100Mbps device. It flashes green  
when data is being transmitted or received on the working connection.  
Link/Act LED: This indicator will light solid green when the corresponding  
port is connected correctly. It flashes green when data is being transmitted or  
received on the working connection.  
3.2 Rear Panel  
The rear panel of the TL-SL1351 features a power receptacle, which is an AC  
power receptacle. Connect the female of the power cord head here, and the male  
head to the AC power outlet.  
Figure 3-2 TL-SL1351 Switch Rear Panel sketch  
5
 
   
Appendix A: Specifications  
General  
IEEE802.3 10Base-T  
IEEE802.3u 100Base-TX  
IEEE802.3ab 1000Base-T  
Standards  
IEEE802.3z 1000Base-X (for TL-SL1351 only)  
ANSI/IEEE Std 802.3 Nway  
IEEE802.3x  
Protocol  
CSMA/CD  
Ethernet: 10Mbps (Half Duplex), 20Mbps (FullDuplex)  
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex)  
Gigabit Ethernet: 2000Mbps (Full Duplex)  
Star  
Data  
Transfer  
Rate  
Topology  
UTP category 3, 4, 5 cable (maximum 100m)  
10Base-T:  
EIA/TIA-568 100STP (maximum 100m)  
UTP category 5, 5e cable (maximum 100m)  
100Base-TX:  
EIA/TIA-568 100STP (maximum 100m)  
Network  
Media  
1000Base-T: UTP category 5, 5e cable (maximum 100m)  
62.5 u m multi mode fiber (maximum 275m)  
50 u m multi mode fiber (maximum 550m)  
62.5 u m multi mode fiber (maximum 550m)  
50 u m multi mode fiber (maximum 550m)  
1000Base-SX (for  
TL-SL3151 only):  
(Cable)  
1000Base-LX (for  
TL-SL3151 only):  
9 u m/10 u m single mode fiber (maximum  
5km)  
8/16/24/48 10/100Mbps Auto-Negotiation RJ-45 ports  
2/1/2/2 10/100/1000Mbps Auto-Negotiation RJ-45 ports  
1 SFP module Interface (for TL-SL1351 only)  
Number of  
Ports  
6
 
   
Auto MDI/MDI-X cable detection, Each port can be used Uplink  
ports  
Uplink Ports  
Transfer  
Method  
Store-and-Forward  
MAC  
Address  
Table  
8k, Automatically learning, automatically Update  
10Base-T: 14880pps/Port  
100Base-TX: 148810pps/Port  
Frame Filter  
Rate  
1000Base-T: 1488095pps/Port  
1000Base-X: 1488095pps/Port (for TL-SL1351 only)  
10Base-T: 14880pps/Port  
Frame  
Forward  
Rate  
100Base-TX: 148810pps/Port  
1000Base-T: 1488095pps/Port  
1000Base-X: 1488095pps/Port (for TL-SL1351 only)  
Safety &  
FCC, CE  
Emissions  
Environmental and Physical  
Operating  
0°C ~40°C  
Temperature  
Storage Temperature -40°C ~70°C  
Operating Humidity  
Storage Humidity  
10%~90% non-condensing  
5%~90% non-condensing  
7
 
 

The Singing Machine CD Player SMG 158 User Manual
Toastmaster Fryer TES1CAN User Manual
Topcom Telephone 5710 User Manual
Toshiba CRT Television 27A45C User Manual
Toshiba DVD Player RD XS30B User Manual
Toshiba Printer B EP2DL User Manual
Transcend Information Computer Drive microSD User Manual
Tripp Lite Surge Protector 10+TEL DBS User Manual
Vantec Power Supply VDK PSU User Manual
VDO Dayton Car Satellite TV System DTV 6500 User Manual