Theta Digital Stereo Amplifier Intrepid User Manual

THETA DIGITAL  
C
O
R
P
O
R
A
T
I
O
N
Intrepid  
Owner’s Manual  
 
The lightning flash with arrowhead symbol, within an equilateral  
triangle, is intended to alert the user to the presence of uninsulated  
“dangerous voltage” within the product’s enclosure that may be of  
significant magnitude to constitute a risk of electric shock to persons.  
The exclamation point within an equilateral triangle is intended to alert  
the user to the presence of important operating and maintenance  
(servicing) instructions in the literature accompanying the product.  
WARNING  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,  
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE  
CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THE AC (POLARIZED) PLUG WITH AN  
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY  
INSERTED TO PREVENT BLADE EXPOSURE.  
Extension cords are not recommended for use with this product.  
ii  
 
Intrepid Identification Record  
This information is for your records and for future identification of the Intrepid. Please take a moment to fill  
out all pertinent data now, and as upgrades and/or options are installed. Whenever upgrades, inquiries  
and/or changes are requested, the serial number will be required.  
SERIAL NUMBER  
DATE PURCHASED  
DEALER’S NAME  
DEALER’S ADDRESS/PHONE  
INSTALLED CARDS/OPTIONS  
(Date of installation)  
(Date of installation)  
(Date of installation)  
iii  
 
SAFETY PRECAUTIONS  
Please carefully read each item of the operating instructions and safety precautions before installing and  
using this product. Use extra care to follow the warnings written on the product itself and/or in the operating  
instructions. Keep the operating instructions and safety precautions for future reference.  
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE ANY OF THE COVER  
PANELS.  
NO USER-SERVICEABLE PARTS INSIDE.  
PERSONNEL ONLY.  
REFER ALL SERVICING TO QUALIFIED SERVICE  
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT ALLOW LIQUIDS TO SPILL OR OBJECTS TO FALL  
INTO ANY OPENINGS OF THE PRODUCT.  
THIS UNIT IS SUPPLIED WITH A 3 PIN GROUNDED AC PLUG. ALWAYS INSERT THE AC PLUG INTO  
A GROUNDED OUTLET. DO NOT REMOVE THE GROUND PIN OR DISABLE THE GROUND FOR ANY  
PURPOSE.  
BEFORE MAKING ANY CONNECTIONS TO THE INTREPID, FIRST TURN OFF THE POWER AND THEN  
DISCONNECT THE AC POWER CORD.  
WHEN INSTALLING THE INTREPID IN YOUR SYSTEM, MAKE CERTAIN TO ALLOW A MINIMUM OF ½  
INCH OF VENTILATION ON EACH SIDE OF THE UNIT. ALSO ALLOW AT LEAST 3 INCHES OF  
VENTILATION SPACE ABOVE THE UNIT. IMPROPER VENTILATION OF THE UNIT MAY CAUSE  
OVERHEATING, WHICH MAY DAMAGE THE UNIT AND CAUSE A FIRE. PLACE THE UNIT ON A  
SOLID SURFACE ONLY. I.E. NOT ON CARPET, ETC.  
DO NOT PLACE THE INTREPID NEAR HEAT SOURCES SUCH AS DIRECT SUNLIGHT, STOVES, HEAT  
REGISTERS, RADIATORS OR OTHER HEAT PRODUCING EQUIPMENT.  
TO PREVENT DAMAGE TO THE ANALOG OUTPUT CIRCUITRY, BE CERTAIN NOT TO SHORT THE  
OUTPUT SIGNAL TO GROUND. ENSURE THAT YOUR AUDIO OUTPUT CABLES DO NOT HAVE ANY  
INTERNAL SHORTS BEFORE CONNECTING THEM TO THE INTREPID.  
IF REPLACEMENT OF THE AC LINE FUSE AND/OR ANY INTERNAL FUSE BECOMES NECESSARY,  
REPLACE ONLY WITH SAME VALUE AND TYPE OF FUSE. NEVER BYPASS THE FUSE.  
IF THE AC CORD BECOMES DAMAGED, DO NOT USE IT. IMMEDIATELY REPLACE IT WITH A NEW  
ONE OF THE SAME OR BETTER RATING.  
IT IS IMPERATIVE THAT THE INTREPID BE OPERATED IN A WELL VENTILATED ENVIRONMENT AND  
THE IMMEDIATE EXTERNAL TEMPERATURE BE MAINTAINED AS SPECIFIED. EXTERNAL COOLING  
FANS MAY BE REQUIRED IN SOME CASES. DO NOT STACK ANY EQUIPMENT DIRECTLY ABOVE  
OR BELOW THE INTREPID AS TO PROTECT IT FROM OVERHEATING, AS WELL AS THE  
CONTINUED FUNCTIONALITY OF ANY EQUIPMENT NEAR AND AROUND IT.  
EACH CHANNEL IS A BALANCED BRIDGE AMPLIFIER, THUS THE NEGATIVE SPEAKER TERMINAL  
IS NOT A GROUND, AND CANNOT BE CONNECTED TO A SYSTEM GROUND OR LOUDSPEAKER  
SYSTEM WITH A COMMON GROUND. CONSULT YOUR SPEAKER MANUFACTURER TO ENSURE  
THAT ANY SPEAKER IN YOUR SYSTEM THAT WILL BE CONNECTED TO THE INTREPID DOES NOT  
HAVE INTERNAL CIRCUITRY WITH A COMMON GROUND.  
AFTER MARKET and THIRD PARTY MODIFICATIONS  
Please note that any after market and/or third party modifications will void the warranty. In the case of  
changing the feet on a unit, in order to prevent any damage (which will also not be covered under warranty),  
please verify that the screws being used to secure non-Theta feet do not screw any deeper into the chassis  
than the original ones. The original screw is 1/4-20 by 1/2 and goes into the chassis 1/4 inch.  
iv  
 
Table of Contents  
PREFACE ........................................................................................................................................................... i  
WARNING...................................................................................................................................................... ii  
Intrepid Identification Record..........................................................................................................................iii  
SAFETY PRECAUTIONS ............................................................................................................................. iv  
INTRODUCTION................................................................................................................................................ 1  
Getting to know your Intrepid ......................................................................................................................... 1  
Burn-In Time................................................................................................................................................... 1  
Reference Manual Conventions..................................................................................................................... 1  
IMPORTANT NOTICE.................................................................................................................................... 2  
Intrepid Block Diagram ................................................................................................................................... 3  
Front Panel Layout ......................................................................................................................................... 4  
Rear Panel Layout.......................................................................................................................................... 5  
OPERATION...................................................................................................................................................... 6  
Connecting the Intrepid .................................................................................................................................. 6  
Remote Trigger............................................................................................................................................... 6  
RS232............................................................................................................................................................. 6  
Appendix A  
Appendix B  
Appendix C  
Troubleshooting Guide.......................................................................................................... 7  
Wiring Diagram ..................................................................................................................... 8  
RS232 Protocol..................................................................................................................... 9  
RS232 Jumper Settings............................................................................................................................ 12  
Appendix D  
Specifications...................................................................................................................... 13  
v
 
INTRODUCTION  
Getting to know your Intrepid  
This Intrepid has been put through a rigorous and unique testing procedure that ensures that it will last for  
many years with minimal service requirements. This procedure includes the following:  
All assembled circuit boards are given a thorough visual inspection and are then tested in a bench-  
reference Intrepid.  
The tested, assembled circuit boards are then installed in a new Intrepid and the whole unit is tested  
for every function and parameter.  
The unit is put on a burn-in torture rack to test for any possible component failures.  
It is then tested on an audio analyzer for all pertinent parameters.  
The unit has all remaining chassis components installed and then undergoes a complete visual  
inspection, which assures that all Intrepids meet visual specifications.  
The Intrepid then undergoes a critical listening and functional test.  
Burn-In Time  
This unit has a break in period of about 1 week during which continuous improvement in sound quality will be  
observed. It is recommended that music be played continuously through the unit during this time to expedite  
the break in period.  
Reference Manual Conventions  
For clarity purposes, references to buttons and LED’s will be shown in bold capital letters.  
1
 
IMPORTANT NOTICE  
I.  
It is imperative that the Intrepid be connected to a ground via its three wire AC power cord. It is  
important that the AC power outlet, which the Intrepid is plugged into, is actually grounded. Failure  
to do so will severely compromise the performance, reliability and safety of use of the Intrepid.  
II.  
III.  
Ventilation is an important issue when placing the Intrepid in a system. Make certain that the Intrepid  
is placed in a well-ventilated area or rack unit. Heat must be dissipated and cool air must be allowed  
to enter the Intrepid.  
Please take note that some powerline conditioners defeat the AC power ground on their outlets. If  
the intention is to plug the Intrepid into a line conditioner, check with your dealer to make certain that  
the particular conditioner that is intended for use DOES NOT DEFEAT THE AC GROUND on its AC  
outlets. Only the highest powered line conditioners should be considered for use with the Intrepid.  
Otherwise, the amplifier’s power output may be compromised.  
IV.  
V.  
DO NOT remove any cover panels from the Intrepid, as there are no user serviceable components  
inside. Refer servicing and updating to qualified service personnel only.  
Endcaps (NOT shorting plugs) on all unused RCA inputs will improve the sound quality and may  
reduce the susceptibility to RF induced anomalies.  
VI.  
It is imperative that the Intrepid be operated in a well ventilated environment and the immediate  
external temperature be maintained as specified in Appendix D of this manual. External cooling fans  
may be required in some cases. Do not stack any equipment directly above or below the Intrepid as  
to protect it from overheating, as well as the continued functionality of any equipment near and  
around it.  
VII.  
Each channel is a balanced bridge amplifier, thus the negative speaker terminal is NOT a ground,  
and cannot be connected to a ground or a loudspeaker system with a common ground. Consult your  
speaker manufacturer to ensure that any speaker in your system that will be connected to the  
Intrepid does NOT have internal circuitry with a common ground.  
2
 
 
Front Panel Layout  
Figure 2 - Front Panel Layout  
1. STANDBY button. After the rear panel MAIN POWER switch is turned on press the front panel STANDBY button  
to exit the standby mode. All channels will come out of standby.  
2. STANDBY LED. Illuminates red when the power amplifier is in STANDBY, green when the amplifier is active.  
3. THERMAL LED. Illuminates when any channel’s temperature rises above the maximum operating temperature  
and puts the Intrepid into standby.  
4
 
Rear Panel Layout  
Figure 3 – Rear Panel Layout showing the optional RS-232 Jacks installed  
1. BINDING POST. Connect plus and minus speaker wires for one speaker to appropriately marked terminals of  
each post. The binding posts can accept spade lugs, banana plugs or bare wire.  
2. SINGLE-ENDED input jack.  
3. BALANCED input jack.  
4. AC POWER INPUT.  
5. Rear panel FUSE. If necessary, replace with same type and rating only.  
6. Main Power Switch. Master power switch. Disconnects AC to all circuits. It is recommended that this be left ON  
at all times during regular use with the exception of whenever cables are connected/disconnected or when the  
unit is not going to be used for an extended period of time.  
7. STANDBY REMOTE TRIGGER jack. When the rear panel STANDBY TRIGGER jack receives a 5-12 VDC pulse  
the Intrepid will change its mode from either standby to operate, or operate to standby, depending on its current  
mode.  
8. DB9 RS232 connector. Used for connecting an external controller to the Intrepid to control and monitor its  
functions.  
9. RJ45 RS232 connector. See DB9 RS232 connector.  
5
 
OPERATION  
Before turning on the Intrepid, ensure that all precautions and warnings have been carefully reviewed and  
adhered to. Damage to the Intrepid caused by improper operation, wiring and/or ventilation will not be  
covered under warranty and Theta will not be liable for any consequential damage or loss.  
Connecting the Intrepid  
With the Intrepid’s rear panel main power switch turned off, connect the signal outputs of each  
preamp/processor channel to either the single-ended or balanced input of the Intrepid. Connect each  
channel output to the input of the speaker that is intended to be driven. Please refer to figure 4.  
Please Note: Each channel is a balanced bridge amplifier, thus the negative speaker terminal is NOT a  
ground, and cannot be connected to a ground or a loudspeaker system with a common ground. Consult  
your speaker manufacturer to ensure that any speaker in your system that will be connected to the Intrepid  
does NOT have internal circuitry with a common ground.  
Connect a 12V pulse trigger source to the trigger input of the Intrepid, if it is desired to be taken in and out of  
standby via another device.  
If the Intrepid’s functionality is to be controlled from a remote controller via RS232, connect the RS232 cable  
between the Intrepid and the controller.  
When first turning on the rear panel power switch, the red STANDBY LED on the front panel will illuminate,  
indicating that all channels are in standby mode. When in standby, the signal is muted and the output bias of  
each channel is reduced to approximately 40 percent.  
Remote Trigger  
When the rear panel STANDBY TRIGGER jack receives a 5-12 VDC pulse, the Intrepid will change its state  
from either standby to operate, or operate to standby, depending on what the current state is.  
RS232  
RS232 is an option in the Intrepid. It can be installed at any time either at the factory or by an authorized  
Theta dealer. All functions of the Intrepid can be controlled and monitored via RS232, using either the RJ45  
or DB9 connector. As long as the rear panel power switch in turned on, the RS232 circuitry is always active,  
thus allowing the Intrepid to be taken out of STANDBY via RS232.  
6
 
Appendix A  
Troubleshooting Guide  
If the Intrepid should function abnormally during operation, please review the items in the following checklist.  
Please be sure to thoroughly check all other connected components such as speakers, preamplifiers, as well  
as cables.  
Symptom  
Possible Cause(s)  
Remedy  
No power or front panel Power cable is not inserted 100% into AC Ensure that the AC cord is inserted all the  
lights and no sound.  
input connector.  
way into the Intrepid and that the wall outlet  
is active.  
Rear panel fuse is open.  
Circuit breaker is open (AC outlet).  
Replace with same type and rating ONLY.  
Check the AC outlet circuit breaker and reset,  
if necessary, or contact your dealer.  
If the front panel THERMAL LED is  
illuminated, shut down the Intrepid until it  
cools. An external fan may be necessary.  
No audio output.  
Hot/Warm  
Overheating  
Normal operation  
7
 
Appendix B  
Wiring Diagram  
This section provides an example illustration of an input and output wiring scheme. Before making any connections,  
please turn off ALL audio and video devices. Unplug those that do not have a main power switch. It is recommended  
that all cables, including speaker cables be kept as short as possible for best sound quality.  
Figure 4 - Examples of Typical Input and Output Connections  
------------ = optional connection.  
WARNING: Each channel is a balanced bridge amplifier, thus the negative speaker terminal is NOT a ground, and  
cannot be connected to a ground or a loudspeaker system with a common ground. Consult your speaker  
manufacturer to ensure that any speaker in your system that will be connected to the Intrepid does NOT have internal  
circuitry with a common ground. Damage will occur if the negative terminal is connected to ground, or to a terminal of  
another channel or module.  
8
 
Appendix C  
RS232 Protocol  
RS232 settings are internally definable via jumper blocks, to accommodate interfacing with a wide range of control  
products.  
Baud rate  
9600 or 19200  
Echo status  
AUTO or REQUEST  
Baud rate:  
Echo status:  
Maximum number of bits per second. The duration of a single bit is equal to 1 / baud rate.  
Specifies whether the STATUS of each parameter shown in the protocol will automatically (AUTO) be  
echoed back to the controller when there is any change, or whether the user must manually request  
(REQ) the status information be sent to the controller. Please refer to page 12 or information on  
changing these settings.  
All commands will follow the format:  
<Header><Command Identifier><Argument 1><Argument 2><Argument 3>  
where:  
<Header> = <FEh><EEh>  
<Command identifier> = <byte>  
<Argument x> = <byte>  
Each command will be able to access the system configuration directly, eliminating the need to press any button on  
the Intrepid front panel.  
Example:  
1) To put the Intrepid into standby: Send FE, EE, 01, 00, 00, 00 (all values in Hex).  
Where FE and EE are the header, 01 = command, 00 = main standby, 00 = put unit in standby and 00 = filler  
(4 characters required)  
9
 
 
RS232 Hardware Connections  
Figure 5 – Intrepid RS232 Jack Pinout  
11  
 
Figure 6 – Intrepid RS232 Jumper Settings  
RS232 Jumper Settings  
There are 2 possible Baud rates: 9600 and 19200. The factory default is 19200. To change the baud rate to 9600,  
move the jumper to the center and top pins (if the RS232 board is orientated as in figure 6).  
The STATUS can be returned to the controller either: automatically every time a parameter has changed, or the user  
can request it manually. The factory default is AUTO. To set the Echo STATUS to return Status information only  
upon request, move the AUTO/REQ jumper to the top pins, or nearer to REQ on the RS232 board.  
The three SELECT jumpers are not currently implemented.  
12  
 
Appendix D  
Specifications  
Inputs:  
Analog audio:  
1 Single-ended per channel (RCA).  
1 Balanced per channel (XLR).  
Input Impedance: 50 KΩ  
Single-Ended or Balanced, for each phase.  
Input sensitivity:  
Gain:  
(Single-Ended) 1.5V RMS input for 100W into 8 ohms.  
(Balanced) 0.75V RMS input for 100W into 8 ohms.  
(Single-Ended) 25.5dB (19x).  
(Balanced) 31.5dB (38x).  
Polarity:  
(Single-Ended) Non-Inverting.  
(Balanced) Pin-2 = Positive, Pin-3 = Negative for Non-Inverting Output.  
Outputs:  
Analog Audio:  
1 balanced output per channel.  
I/O  
RS232: 1 DB9 and 1 RJ45 connector.  
Modes/Processes:  
Standby:All channels are muted and output bias is reduced to 40%.  
Thermal:One or more channels has overheated; amp automatically switches to Standby.  
Power Output:  
(8 ohms-one channel driven)  
(8 ohms-five channels driven)  
(4 ohms-one channel driven)  
100 W (rated)  
100 W (rated)  
200 W (rated)  
130 W (typical)  
115 W (typical)  
210 W (typical)  
Frequency Response:  
THD+Noise:  
(-3dB points @ full power) 0.9 Hz - 350 KHz.  
<2%  
Signal to Noise Ratio:  
Power Requirements:  
Power Consumption:  
(unweighted) >100dB  
117 VAC, 7.7 amp; 230 VAC, 4 amp; 50-60 Hz; for full power in all channels.  
80W @ Standby; 100W @ idle; 900W @ full power.  
Standby Trigger Input: 5-12 VDC Pulse between 1 and 500mS.  
Dimensions:  
Weight:  
17 5/8" W x 6 1/4" H x 20 1/2" D (448 x 159 x 521 mm)  
58 Lbs. Stand alone (26.3 Kg), 64 Lbs. Boxed with accessories (29 Kg)  
Maximum Operating Temperature:  
Internal: 176° F (80° C)  
Room: 131° F (55° C)  
13  
 
90 DAY LIMITED WARRANTY TERMS AND CONDITIONS  
(3 Year optional extended service contract)  
1.  
2.  
Theta Digital Corporation, henceforth referred to as Theta, warrants the product designated herein to be free of  
manufacturing defects in material and workmanship, subject to the conditions set forth herein, for a period of 90 days  
from the date of purchase by the original purchaser, henceforth referred to as purchaser. If the purchaser registers the  
unit with Theta by mailing in the warranty card, together with a copy of the bill of sale, within 14 days of the date of  
purchase, said purchaser will be registered for an extended service contract. The extended service contract extends  
the 90 days to a period of 3 years from the date of purchase by the original purchaser or no later than 7 years from the  
date of shipment to the authorized Theta dealer, whichever comes first.  
CONDITIONS  
This warranty is subject to the following conditions and limitations. The warranty is void and inapplicable if the product  
has been used or handled other than in accordance with the instructions in the owner's manual, abused or misused,  
damaged by accident or neglect or in being transported, or if the defect is due to the product being repaired or  
tampered with or modified by anyone other than Theta or an authorized Theta repair center. In the unlikely event that  
the unit requires service, contact Theta for an RA (Return Authorization) number. The product must be packed and  
returned to Theta or an authorized Theta repair center by the customer at his or her sole expense. Theta will pay  
return freight of its choice. A returned product must be accompanied by a written description of the defect, a photocopy  
of the original purchase receipt, and a daytime phone number where the owner can be reached. The unaltered receipt  
must clearly list model and serial number, the date of purchase, the name and address of the purchaser and authorized  
dealer and the purchase price. Theta reserves the right to modify the design of any product without obligation to  
purchasers of previously manufactured products and to change the prices or specifications of any product without  
notice or obligation to any person.  
3.  
REMEDY  
In the event the above product fails to meet the warranty, and the above conditions have been met, the purchaser's  
sole remedy under the limited warranty shall be to obtain an RA number and return the product to Theta or an  
authorized Theta repair center where the defect will be rectified without charge for parts or labor.  
4.  
5.  
LIMITED TO ORIGINAL PURCHASER  
This warranty is for the sole benefit of the original purchaser of the covered product and shall not be transferred to a  
subsequent purchaser of the product.  
DURATION OF WARRANTY  
This warranty expires 90 days after the date of original purchase. If Theta receives the completed warranty registration  
card within 14 days of original purchase, this period is extended to the third anniversary of the original date of purchase  
or no later that the seventh anniversary of the shipment to the authorized Theta dealer, whichever comes first.  
6.  
7.  
MISCELLANEOUS  
ANY IMPLIED WARRANTIES RELATING TO THE ABOVE PRODUCT SHALL BE LIMITED TO THE DURATION OF  
THIS WARRANTY. THE WARRANTY DOES NOT EXTEND TO ANY INCIDENTAL OR CONSEQUENTIAL COSTS  
OR DAMAGES TO THE PURCHASER. Some states do not allow limitations on how long an implied warranty lasts or  
an exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply  
to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
WARRANTOR  
Inquiries regarding the above limited warranty may be sent to the following address:  
THETA DIGITAL CORPORATION  
5330 DERRY AVENUE, SUITE "R"  
AGOURA HILLS, CA 91301  
WARRANTY OUTSIDE THE USA  
Theta has formal distribution in many of the countries of the free world, in each country the Theta Importer has  
contractually accepted the responsibility for product warranty. Warranty service should normally be obtained from the  
importing dealer or distributor from whom you obtained your product.  
WARNINGS  
1. To prevent fire or shock hazard, do not expose your Theta product to rain or moisture.  
2. This unit contains voltages which can cause serious injury or death. Do not operate with covers removed. Refer all  
servicing to your authorized Theta dealer.  
3. For continued protection against fire hazard, replace fuses only with the same type and rating of fuses as specified.  
GB 1.01  
14  
 

Teac Landscape Lighting SR L35CD User Manual
Terraillon Doll TPRO4300 User Manual
Thermador Cooktop CIT365DS User Manual
The Speaker Company Barcode Reader TDP 225 User Manual
Topcom Telephone COCOON 85 User Manual
Toshiba DVD Player SD 3960 User Manual
Transition Networks Power Supply CPSMP 130 User Manual
ViewSonic Digital Photo Frame DF11GBK User Manual
Vivotek Security Camera IP7330 User Manual
VTech Telephone 5831 User Manual